HP NetRAID SETCLASS Utility
---------------------------
batch file name:   SETCLASS.BAT (invokes _setclss.exe)

executable file name:  "_setclss.exe"
executable file date:   October 16, 2000
executable version:     2.1

This utility supports the following HP NetRAID adapters:
  HP NetRAID-1Si (FW F.01.03 or newer)
  HP NetRAID-3Si (FW C.01.10 or newer)
  HP NetServer LH 3 integrated HP NetRAID (FW D.02.02 or newer)
  HP NetServer LH 4 integrated HP NetRAID (FW D.02.02 or newer)
  HP NetServer LH 3000  integrated HP NetRAID (all FW versions)
  HP NetServer LH 6000  integrated HP NetRAID (all FW versions)
  HP NetServer LT 6000r integrated HP NetRAID (all FW versions)

  Note: The NetRAID (D4943) and NetRAID-1 (D4992) adapters do not
        support I2O (Intelligent I/O). The PCI Class Code for 
        these adapters are "mass storage" and cannot be changed by
        this utility.

Purpose:   To display or change the NetRAID's PCI Class Code
           setting.

Some network operating systems require the NetRAID's
PCI Class Code be set to "mass storage" when using
the non-I2O NetRAID driver. See the table below.

  Network OS           Driver         PCI Class Code
  ----------           ------         --------------
  Unixware 7           mega           "mass storage"
  NT 3.51, 4.0         mraidnt.sys    doesn't matter
  NW 3.x, 4.11, 5      mega4_xx.ham   doesn't matter
  OS/2 Warp 3          mraid.add      doesn't matter
  OS/2 for e-business  mraid.add      "mass storage"
  SCO Unix 5.0.4       amird          doesn't matter
  Unixware 2.1.x       mega           doesn't matter

Warning:   For a given system, all NetRAID adapters (excluding the 
           NetRAID/NetRAID-1) must have the same PCI Class Code
           setting, i.e., all "mass storage" or all "I2O".

SETCLASS Syntax:
   setclass -d
     (display current PCI Class Code settings)

   setclass -m {adapter_number}
     (sets the PCI Class Code for the specified NetRAID adapter
      to "mass storage")

   setclass -i {adapter_number}
     (sets the PCI Class Code for the specified NetRAID adapter
      to "I2O")

Example #1:  setclass -d
   This will display the following information for each adapter:
     "Adapter"     - The NetRAID adapter number
     "Type"        - The type of NetRAID, where:
                       "428" = NetRAID/NetRAID-1
                       "438" = NetRAID-3Si
                       "466" = NetRAID-1Si
                       "T5"  = integrated HP NetRAID (LH3/LH4)
                       "UNKN"= integrated HP NetRAID (LH3000/
                                  LH6000/LT6000r)
     "BusNo"       - PCI bus number for the adapter
     "DevId"       - PCI device ID for the adapter
     "StorageType" - The PCI Class Code, where:
                       "mass" = mass storage
                       "I2O"  = I2O

Example #2:  setclass -m 5
   This will set the PCI Class Code for NetRAID adapter number 5
   to "mass storage"

The PCI Class Code setting can also be changed via the NetRAID 
Express Tools utility. To enter the NetRAID Express Tools utility 
press "<CTRL>M" after the NetRAID banner during system boot up.

[ end of document ]