QL 4222
Chapter 8 - QL Files

Directory Tree

The QL installation utility installs many files on the designated file server. A directory tree of these files is included below (separate trees are provided for the QL 3000 Series and the QL 4000 Series products). A brief description of files requiring explanation is provided. A listing of the key configuration files is included later in this chapter

QL 3000 Series Tree

QL 4000 Series Tree

QL 3000 Series Remote Boot Files

CONFIG.SYS

File: SYS:CUBIX/QL3000/IMAGE32/VLM/CONFIG.SYS

device=qlsetup.sys -t
device=himem.sys /testmem:off
device=emm386.exe /y=f:\login\emm386.exe I=b000-b7ff I=cc00-edff I=f000-f7ff x=c000-cbff x=ee00-efff noems
shell=command.com /p /e:500
devicehigh=ansi.sys
dos=umb
dos=high
stacks=9,256
files=60
fcbs=4,0
buffers=15,0
lastdrive=z

NOTE: For the QL 3001 and QL 3002, the command /m:6 must be appended to the command to load himem.sys as follows:

device=himem.sys /testmem:off /m:6

The line is correct in the in the SYS:CUBIX/QL3000/IMAGE30/VLM/CONFIG.SYS file. The file above represents the CONFIG.SYS file in the SYS:/CUBIX/QL3000/IMAGE32/VLM directory.

Note: The "/y" switch on the emm386 command is a Microsoft Windows switch. If Windows is run on the QL workstation and the "/y" switch is not specified, Windows will load in standard mode. The "/y" switch must be specified is Windows is to run in enhanced mode on the QL workstation. If Windows will not be run on the QL workstation, the "/y" switch can be left on the emm386 command line (it will not cause any problems).

A copy of emm386.sys must exist in the path specified by the "/y" switch (f:\login in the file listed above).

AUTOEXEC.BAT

File: SYS:CUBIX/QL3000/IMAGE32/VLM/AUTOEXEC.BAT

@echo off
rem *************************************************
rem * AUTOEXEC.BAT
rem *
rem * Cubix Corporation
rem * 2800 Lockheed Way, Carson City, NV 89706
rem *************************************************
rem *
rem * Invoke the Cubix QL3BOOT.BAT file with the
rem * DOS 'loadhigh' option.
ql3boot.bat loadhigh

 

QL3B00T.BAT

File: SYS:CUBIX/QL3000/IMAGE32/VLM/QL3BOOT.BAT

@echo off
cls
rem *************************************************
rem * QL3BOOT.BAT
rem *
rem * Cubix Corporation
rem * 2800 Lockheed Way, Carson City, NV 89706
rem *************************************************
rem * Begin the normal IPX boot Process for ODI.
rem *
rem * Load the NetWare Link Support Layer driver.
rem * If a command line parameter was specified
rem * when QL3BOOT.BAT was run (e.g. QL3BOOT.BAT
rem * LH), use that parameter here.
%1 lsl.com
rem *
rem * Load the Cubix QL 3000 Series Workstation
rem * Driver for ODI. If a command line parameter
rem * was specified when QL3BOOT.BAT was run (e.g.
rem * QL3BOOT.BAT LH), use that parameter here.
%1 ql3_dos.com
rem *
rem * Load the NetWare IPXODI.COM driver.
rem * Loading IPXODI.COM high can cause problems
rem * with SPX communications, so IPXODI.COM will
rem * be loaded in low memory here.
ipxodi.com
rem *
rem * Execute QLNODE.EXE which initializes the DOS
rem * environment variables as follows:
rem * QLNODE - QL processor node number
rem * QLLDRV - DOS last drive
qlnode
set comspec=y:command.com
rem *
rem * Load the NetWare DOS Requester (VLMs).
rem *
vlm.exe /Mx
rem *
rem * Load the NetWare SNMP/IPX transport provider
stpipx.com /c=f:cmsnet.cfg
rem *
rem * Change to the drive specified by the
rem * environment variable QLLDRV
rem * (set by the program QLNODE above).
%QLLDRV%:
rem *
rem * Clear the environment variable QLLDRV to save
rem * space.
set QLLDRV=
rem *
rem * If a custom QL user batch file exists for
rem * this node number, execute it.
if exist qlusr%QLNODE%.bat qlusr%QLNODE%.bat %1
rem *
rem * If no custom QL user batch file exists for
rem * this node number, execute the default
rem * QLUSER.BAT file.
if exist qluser.bat qluser.bat %1

NET.CFG

File: SYS:CUBIX/QL3000/IMAGE32/VLM/NET.CFG

preferred server = designated server

link driver ql3_dos

frame Token-Ring
protocol IPX E0 Token-Ring

NetWare DOS Requester

checksum = 0
first network drive = f
cache buffer size = 2484
VLM = wssnmp.vlm
VLM = wstrap.vlm
VLM = wsreg.vlm
VLM = wsasn1.vlm
VLM = mib2if.vlm
vlm = cbxnode.vlm

Cubix Node Agent

TrapInterval = 30
SupervisorAddress = QL Supervisor IPX Address
DeviceType = ql

Protocol IPX

spx connections 35

NOTE: designated server will be replaced by the name of the designated server specified during QL installation.

NOTE: If the Cubix Management System (CMS) is to manage the QL workstation, the TrapInterval specifies the number of seconds between status messages generated by the QL workstation. Do not modify this setting without first consulting the CMS documentation.

NOTE: The installation utility will set the QL Supervisor IPX Address to the address of the QL Supervisor NLM if the QL boards are installed in the backplane of the designated server. If the QL boards are installed in another device, set this field to the IPX address of the QL Supervisor NLM installed on the server or MPR containing the QL processor. Instructions for setting this field are included in Chapter 2 - Installation.

CMSNET.CFG

Transport Provider IPX

; trap target = 00000000:000000000000

NOTE: If the Cubix Management System (or another SNMP compliant management system) is to manage the QL workstation, the trap target must be set to the IPX address of the management console. Also remove the semicolon (";") from the beginning of the line.

QL 4000 Series Remote Boot Files

CONFIG.SYS

File: SYS:CUBIX/QL4000/IMAGE/VLM/CONFIG.SYS

device=qlsetup.sys -t
device=himem.sys /testmem:off
device=emm386.exe /y=f:\login\emm386.exe I=b000-b7ff I=d000-f7ff x=C000-CFFF noems
buffers=15,0
files=60
dos=umb
lastdrive=z
fcbs=4,0
devicehigh=ansi.sys
shell=command.com /p /e:500
dos=high
stacks=9,256

NOTE: The "/y" switch on the emm386 command is a Microsoft Windows switch. If Windows is run on the QL workstation and the "/y" switch is not specified, Windows will load in standard mode. The "/y" switch must be specified is Windows is to run in enhanced mode on the QL workstation. If Windows will not be run on the QL workstation, the "/y" switch can be left on the emm386 command line (it will not cause any problems).

A copy of emm386.sys must exist in the path specified by the "/y" switch (f:\login in the file listed above).

AUTOEXEC.BAT

File: SYS:CUBIX/QL4000/IMAGE/VLM/AUTOEXEC.BAT

@echo off
cls
rem *************************************************
rem * QL4BOOT.BAT
rem *
rem * Cubix Corporation
rem * 2800 Lockheed Way, Carson City, NV 89706
rem *************************************************
rem * Begin the normal IPX boot Process for ODI.
rem *
rem * Load the NetWare Link Support Layer driver.
rem * If a command line parameter was specified
rem * when QL4BOOT.BAT was run (e.g. QL4BOOT.BAT
rem * LH), use that parameter here.
%1 lsl.com
rem *
rem * Load the Cubix QL 4000 Series Workstation
rem * Driver for ODI. If a command line parameter
rem * was specified when QL4BOOT.BAT was run (e.g.
rem * QL4BOOT.BAT LH), use that parameter here.
%1 ql4_dos.com
rem *
rem * Load the NetWare IPXODI.COM driver.
rem * Loading IPXODI.COM high can cause problems
rem * with SPX communications, so IPXODI.COM will
rem * be loaded in low memory here.
ipxodi.com
rem *
rem * Execute QLNODE.EXE which initializes the DOS
rem * environment variables as follows:
rem * QLNODE - QL processor node number
rem * QLLDRV - DOS last drive
qlnode
set comspec=y:command.com
rem *
rem * Load the NetWare DOS Requester (VLMs).
rem *
vlm.exe /Mx
rem *
rem * Load the NetWare SNMP/IPX transport provider
stpipx.com /c=f:cmsnet.cfg
rem *
rem * Change to the drive specified by the
rem * environment variable QLLDRV
rem * (set by the program QLNODE above).
%QLLDRV%:
rem *
rem * Clear the environment variable QLLDRV to save
rem * space.
set QLLDRV=
rem *
rem * If a custom QL user batch file exists for
rem * this node number, execute it.
if exist qlusr%QLNODE%.bat qlusr%QLNODE%.bat %1
rem *
rem * If no custom QL user batch file exists for
rem * this node number, execute the default
rem * QLUSER.BAT file.
if exist qluser.bat qluser.bat %1

NET.CFG

File: SYS:CUBIX/QL4000/IMAGE/VLM/NET.CFG

preferred server = designated server

link driver ql3_dos

frame Token-Ring
protocol IPX E0 Token-Ring

NetWare DOS Requester

checksum = 0
first network drive = f
cache buffer size = 3084
VLM = wssnmp.vlm
VLM = wstrap.vlm
VLM = wsreg.vlm
VLM = wsasn1.vlm
VLM = mib2if.vlm
vlm = cbxnode.vlm

Cubix Node Agent

TrapInterval = 30
SupervisorAddress = QL Supervisor IPX Address
DeviceType = ql

Protocol IPX

spx connections 35

NOTE: designated server will be replaced by the name of the designated server specified during QL installation.

NOTE: If the Cubix Management System (CMS) is to manage the QL workstation, the TrapInterval specifies the number of seconds between status messages generated by the QL workstation. Do not modify this setting without first consulting the CMS documentation.

NOTE: The installation utility will set the QL Supervisor IPX Address to the address of the QL Supervisor NLM if the QL boards are installed in the backplane of the designated server. If the QL boards are installed in another device, set this field to the IPX address of the QL Supervisor NLM installed on the server or MPR containing the QL processor. Instructions for setting this field are included in Chapter 2 - Installation.

CMSNET.CFG

File: SYS:CUBIX/QL4000/LOGIN/CMSNET.CFG

Transport Provider IPX

; trap target = 00000000:000000000000

NOTE: If the Cubix Management System (or another SNMP compliant management system) is to manage the QL workstation, the trap target must be set to the IPX address of the management console. Also remove the semicolon (";") from the beginning of the line.

QLUSER.BAT or QLUSRxxx File

In addition to the CONFIG.SYS, AUTOEXEC, QLxBOOT.BAT, and NET.CFG files, the QL user file (QLUSER.BAT or QLUSRxxx.BAT) is also part of the remote boot process. Unlike the other files, the QL user file is not included in the image file. The last thing that the image file will do is to execute the QL user file, which must be located in the LOGIN directory on the designated server.

The purpose of the QL user file is to provide an easy way for the system installer to invoke applications from a QL workstation without having to modify the image file. This is accomplished by invoking the application from the QL user file.

If all QL processors booting from this designated server will invoke the same application at boot time, they can share a single QL user file (QLUSER.BAT). However, in certain installations some QL nodes may need to invoke different applications than other QL nodes. This is accomplished by using the QLUSRxxx.BAT file, where xxx represents the QL node number.

NOTE: To determine the node number, run QLVision, select the appropriate QL Supervisor, and then run the QL Node Functions option from the Main Menu. The node numbers will be displayed.

When a QL processor boots, it executes the QL3BOOT.BAT or QL4BOOT.BAT file, which will search the LOGIN directory for a QLUSRxxx.BAT file with xxx set to the node number of the booting processor. If a match is found, the QLUSRxxx.BAT file is executed; otherwise, QLUSER.BAT is executed.

For example, if the LOGIN directory on the designated server contains both a QLUSR001.BAT file and a QLUSER.BAT file, the QL processor configured as node 1 will execute QLUSR001.BAT at boot time, while all other QL processors booting from this file server will execute QLUSER.BAT.

The QLUSRxxx.BAT file should be created by copying the default QLUSER.BAT file and then modifying QLUSRxxx as necessary.

QLUSER.BAT

File: SYS:CUBIX/QLx000/LOGIN/QLUSER.BAT

@echo off
rem *************************************************
rem * QLUSER.BAT
rem *
rem * Cubix Corporation
rem * 2800 Lockheed Way, Carson City, NV 89706
rem *************************************************
rem *
rem * Display full path at DOS prompt
prompt $p$g
rem *
rem * Load the Cubix QLRCV TSR. This cannot be
rem * loaded in high memory.
qlrcv
rem *
rem * Perform NetWare LOGIN.
login

QL 3000 DOS Local Boot Files

CONFIG.SYS

The CONFIG.SYS file installed on the hard drive is the same as the SYS:CUBIX/QL3000/HDDRV/CNFGVLM.HD file on the designated server.

device=qlsetup.sys -t
device=c:\dos\himem.sys /testmem:off
device=c:\dos\emm386.exe I=cc00-edff I=b000-b7ff (cont on next line)
I=f000-f7ff x=c000-cbff x=ee00-efff NOEMS
shell=command.com /p /e:500
devicehigh=ansi.sys
dos=umb
dos=high
stacks=9,256
files=60
fcbs=4,0
buffers=15,0
lastdrive=z

AUTOEXEC.BAT

The AUTOEXEC.BAT file installed on the hard drive is the same as the SYS:CUBIX/QL3000/HDDRV/AUTOEXEC.HD file on the designated server.

@echo off
rem *************************************************
rem * AUTOEXEC.BAT for Microsoft DOS 6.22 (or
rem * compatible) and for use with Cubix QL 3222
rem * Series workstation hard drives.
rem *
rem * Cubix Corporation
rem * 2800 Lockheed Way, Carson City, NV 89706
rem *************************************************
rem *
rem * Set up a path to DOS.
path c:\;c:\dos
rem *
rem * Set up the prompt.
prompt $p$g
rem *
rem * Invoke the Cubix QL3000.BAT file with the DOS
rem * 'loadhigh' option.
cd \ql3000
ql3000.bat loadhigh

NET.CFG

The NET.CFG file installed on the hard drive is the same as the SYS:CUBIX/QL3000/HDDRV/NET.HD file on the designated server.

preferred server = designated server

link driver ql3_dos

frame Token-Ring
protocol IPX E0 Token-Ring

NetWare DOS Requester

checksum = 0
first network drive = f
cache buffer size = 2484
VLM = wssnmp.vlm
VLM = wstrap.vlm
VLM = wsreg.vlm
VLM = wsasn1.vlm
VLM = mib2if.vlm
vlm = cbxnode.vlm

Cubix Node Agent

TrapInterval = 30
SupervisorAddress = QL Supervisor IPX Address
DeviceType = ql

Protocol IPX

spx connections 35

NOTE: designated server will be replaced by the name of the designated server specified during QL installation.

NOTE: If the Cubix Management System (CMS) is to manage the QL workstation, the TrapInterval specifies the number of seconds between status messages generated by the QL workstation. Do not modify this setting without first consulting the CMS documentation.

NOTE: The installation utility will set the QL Supervisor IPX Address to the address of the QL Supervisor NLM if the QL boards are installed in the backplane of the designated server. If the QL boards are installed in another device, set this field to the IPX address of the QL Supervisor NLM installed on the server or MPR containing the QL processor. Instructions for setting this field are included in Chapter 2 - Installation.

NOTE: If the Cubix Management System (or another SNMP compliant management system) is to manage the QL workstation, the trap target must be set to the IPX address of the management console.

QL3000.BAT

The QL3000.BAT file installed on the hard drive is the same as the SYS:CUBIX/QL3000/HDDRV/QL3000.HD file on the designated server.

@echo off
rem *************************************************
rem * QL3000.BAT
rem *
rem * Cubix Corporation
rem * 2800 Lockheed Way, Carson City, NV 89706
rem *************************************************
rem *
rem * Clear the screen.
cls
rem *
rem * Print the message "Novell NetWare System
rem * Login".
echo Novell NetWare System Login
rem *
rem * Begin the normal IPX boot Process for ODI.
rem *
rem * Load the NetWare Link Support Layer driver.
rem * If a command line parameter was specified
rem * when QL3000.BAT was run (e.g. QL3000.BAT LH),
rem * use that parameter here.
%1 lsl.com
rem *
rem * Load the Cubix QL 3000 Series Workstation
rem * Driver for ODI. If a command line parameter
rem * was specified when QL3000.BAT was run (e.g.
rem * QL3000.BAT LH), use that parameter here.
%1 ql3_dos.com
rem *
rem * Load the NetWare IPXODI.COM driver.
ipxodi.com
rem *
rem * Execute QLNODE.EXE which initializes the DOS
rem * environment variables as follows:
rem * QLNODE - QL processor node number
rem * QLLDRV - DOS last drive
qlnode
rem *
:DOSREQ
rem *
rem * Set the variable QLLDRV to F. (VLM.EXE will
rem * leave the user in the root of the working
rem * directory and this must be the first
rem * network drive in order to perform login.)
set QLLDRV=f
rem * Load the NetWare DOS Requester Software
rem * (.VLM's).
vlm.exe
rem *
rem * Load the NetWare SNMP\IPX transport provider
rem *
stpipx.com /c=c:\ql3000\cmsnet.cfg
rem *
:LDQLRCV
rem *
rem * Load the Cubix QLRCV TSR. This cannot be
rem * loaded in high memory.
qlrcv
rem *
rem * Change to the drive specified by the
rem * environment variable QLLDRV (set by the
rem * program QLNODE above).
%QLLDRV%:
rem *
rem * Clear the environment variable QLLDRV to save
rem * space.
set QLLDRV=
rem *
rem * Perform NetWare LOGIN.
login

QL 4000 DOS Local Boot Files

CONFIG.SYS

The CONFIG.SYS file installed on the hard drive is the same as the SYS:CUBIX/QL4000/HDDRV/CNFGVLM.HD file on the designated server.

device=qlsetup.sys -t
device=c:\dos\himem.sys /testmem:off
device=c:\dos\emm386.exe I=b000-b7ff I=d000-f7ff x=C000-CFFF NOEMS
buffers=15,0
files=60
dos=umb
lastdrive=z
fcbs=4,0
devicehigh=ansi.sys
shell=command.com /p /e:500
dos=high
stacks=9,256

AUTOEXEC.BAT

The AUTOEXEC.BAT file installed on the hard drive is the same as the SYS:CUBIX/QL4000/HDDRV/AUTOEXEC.HD file on the designated server.

@echo off
rem *************************************************
rem * AUTOEXEC.BAT for Microsoft DOS 6.22 (or
rem * compatible) and for use with Cubix QL 4000
rem * Series workstation hard drives.
rem *
rem * Cubix Corporation
rem * 2800 Lockheed Way, Carson City, NV 89706
rem *************************************************
rem *
rem * Set up a path to DOS.
path c:\;c:\dos
rem *
rem * Set up the prompt.
prompt $p$g
rem *
rem * Invoke the Cubix QL4000.BAT file with the DOS 'loadhigh' option.
cd \ql4000
ql4000.bat loadhigh

NET.CFG

The NET.CFG file installed on the hard drive is the same as the SYS:CUBIX/QL4000/HDDRV/NET.HD file on the designated server.

preferred server = designated server

link driver ql4_dos

frame Token-Ring
protocol IPX E0 Token-Ring

NetWare DOS Requester

checksum = 0
first network drive = f
cache buffer size = 3084
VLM = wssnmp.vlm
VLM = wstrap.vlm
VLM = wsreg.vlm
VLM = wsasn1.vlm
VLM = mib2if.vlm
vlm = cbxnode.vlm

Cubix Node Agent

TrapInterval = 30
SupervisorAddress = QL Supervisor IPX Address
DeviceType = ql

Protocol IPX

spx connections 35

NOTE: designated server will be replaced by the name of the designated server specified during QL installation.

NOTE: If the Cubix Management System (CMS) is to manage the QL workstation, the TrapInterval specifies the number of seconds between status messages generated by the QL workstation. Do not modify this setting without first consulting the CMS documentation.

NOTE: The installation utility will set the QL Supervisor IPX Address to the address of the QL Supervisor NLM if the QL boards are installed in the backplane of the designated server. If the QL boards are installed in another device, set this field to the IPX address of the QL Supervisor NLM installed on the server or MPR containing the QL processor. Instructions for setting this field are included in Chapter 2 - Installation.

NOTE: If the Cubix Management System (or another SNMP compliant management system) is to manage the QL workstation, the trap target must be set to the IPX address of the management console.

QL4000.BAT

The QL4000.BAT file installed on the hard drive is the same as the SYS:CUBIX/QL4000/HDDRV/QL4000.HD file on the designated server.

@echo off
rem *************************************************
rem * QL4000.BAT
rem *
rem * Cubix Corporation
rem * 2800 Lockheed Way, Carson City, NV 89706
rem *************************************************
rem *
rem * Clear the screen.
cls
rem *
rem * Print the message "Novell NetWare System
rem * Login".
echo Novell NetWare System Login
rem *
rem * Begin the normal IPX boot Process for ODI.
rem *
rem * Load the NetWare Link Support Layer driver.
rem * If a command line parameter was specified
rem * when QL4000.BAT was run (e.g. QL4000.BAT LH),
rem * use that parameter here.
%1 lsl.com
rem *
rem * Load the Cubix QL 4000 Series Workstation
rem * Driver for ODI. If a command line parameter
rem * was specified when QL4000.BAT was run (e.g.
rem * QL4000.BAT LH), use that parameter here.
%1 ql4_dos.com
rem *
rem * Load the NetWare IPXODI.COM driver.
ipxodi.com
rem *
rem * Execute QLNODE.EXE which initializes the DOS
rem * environment variables as follows:
rem * QLNODE - QL processor node number
rem * QLLDRV - DOS last drive
qlnode
rem *
:DOSREQ
rem *
rem * Set the variable QLLDRV to F. (VLM.EXE will
rem * leave the user in the root of the working
rem * directory and this must be the first network
rem * drive in order to perform NetWare login.)
set QLLDRV=f
rem * Load the NetWare DOS Requester Software
rem * (.VLM's).
rem *
vlm.exe
rem *
rem * Load the NetWare SNMP\IPX transport provider
rem *
stpipx.com /c=c:\ql4000\cmsnet.cfg
:LDQLRCV
rem *
rem * Load the Cubix QLRCV TSR. This cannot be
rem * loaded in high memory.
qlrcv
rem *
rem * Change to the drive specified by the
rem * environment variable QLLDRV (set by the
rem * program QLNODE above).
%QLLDRV%:
rem *
rem * Clear the environment variable QLLDRV to save
rem * space.
set QLLDRV=
rem *
rem * Perform NetWare LOGIN.
login

QL 3000 OS/2 Local Boot Files

CONFIG.SYS

The CONFIG.SYS file installed on the hard drive is a standard OS/2 CONFIG.SYS file. Only the parts of the file that pertain to the QL driver are listed below.

Appended to LIBPATH should be: C:\NETWARE;

Appended to PATH should be:C:\NETWARE;L:\OS2;P:\OS2;

Appended to DPATH should be:C:\NETWARE;L:\OS2;P:\OS2;

The command to load the MOUSE.SYS device driver should be replaced with the following: DEVICE=C:\OS2\CBXMOUSE.SYS

The CONFIG.SYS file should also contain the following lines. Depending upon options selected during the NetWare Workstation for OS/2 installation, some of the lines indicated as commented out (with the rem statement) may not be commented out in the actual CONFIG.SYS file on the hard drive.

REM --- NetWare Requester statements BEGIN ---
SET NWLANGUAGE=ENGLISH
DEVICE=C:\NETWARE\LSL.SYS
RUN=C:\NETWARE\DDAEMON.EXE
DEVICE=C:\NETWARE\QL3_OS2.SYS
DEVICE=C:\NETWARE\IPX.SYS
rem DEVICE=C:\NETWARE\SPX.SYS
rem RUN=C:\NETWARE\SPDAEMON.EXE
rem DEVICE=C:\NETWARE\NMPIPE.SYS
rem DEVICE=C:\NETWARE\NPSERVER.SYS
rem RUN=C:\NETWARE\NPDAEMON.EXE
DEVICE=C:\NETWARE\NWREQ.SYS
IFS=C:\NETWARE\NWIFS.IFS
RUN=C:\NETWARE\NWDAEMON.EXE
rem DEVICE=C:\NETWARE\NETBIOS.SYS
rem RUN=C:\NETWARE\NBDAEMON.EXE
DEVICE=C:\NETWARE\VIPX.SYS
DEVICE=C:\NETWARE\VSHELL.SYS GLOBAL
REM --- NetWare Requester statements END ---

NOTE: The GLOBAL declaration on the command to load VSHELL.SYS may be PRIVATE in some installations.

NET.CFG

The NET.CFG file installed on the hard drive is the same as the SYS:CUBIX/QL3000/OS2/NET.QL3 file on the designated server.

#***********************************************
#* NET.CFG
#*
#* Cubix Corporation
#* 2800 Lockheed Way, Carson City, NV 89706
#***********************************************
#
# NET.CFG file for QL 3222 OS/2 ODI Workstation
# Driver.
#
Link Support
buffers 20 2154
Protocol Stack SPX
sessions 35

QL 4000 OS/2 Local Boot Files

CONFIG.SYS

The CONFIG.SYS file installed on the hard drive is a standard OS/2 CONFIG.SYS file. The QL specific parts of the CONFIG.SYS file for the QL 4000 Series products are the same as previously described for the QL 3000, except that the device driver loaded is QL4_OS2.SYS instead of QL3_OS2.SYS.

NET.CFG

The NET.CFG file installed on the hard drive is the same as the SYS:CUBIX/QL4000/OS2/NET.QL4 file on the designated server.

#***********************************************
#* NET.CFG
#*
#* Cubix Corporation
#* 2800 Lockheed Way, Carson City, NV 89706
#***********************************************
#
# NET.CFG file for QL 4222 OS/2 ODI Workstation
# Driver.
#
Link Support
buffers 14 4210
Protocol Stack SPX
sessions 35

This document, and all Web contents, Copyright © 1997 by Cubix Corp., Carson City, NV, USA.